Black Box AC2000A Spezifikationen PDF herunterladen (Seite 3)

UNCRATING AND SET-UP

Remove your Series 2000 changer from the shipping box. Open

the door. (The T-handle is a screw-in type and therefor, must be

turned at least 10 times counter-clockwise until it opens.)

Inspect for any connectors or components that may have been

dislodged during shipping. The lock and keys for your changer

will be inside the manila envelope along with this manual. To

install the lock, insert the cylinder into the round hole in the

middle of the T-handle and push until it stops. Now turn the key

and lock until you hear it “snap." Turn the key counter-

clockwise ¼ turn and remove the keys.

NOTE: THE METER ON THE MAIN LOGIC BOARD

CANNOT BE RESET TO ZERO!!!

TEST:

Before permanently installing the changer, do a functional test to

verify that there is no shipping damage to your new changer(s).

Extend the power cord through the hole in the back of the

changer or the bottom and plug it into a grounded 120vac outlet.

The dip switches are already set for a 4 coin per dollar pay-

out of the hoppers, and the Bill validator is ready to accept

$1-$5-$10-$20 dollar bills.

Fill the each hopper with at least 100 coins. On the main logic

board turn the switch on the bottom right corner “ON". (SEE

FIG. 1 ON PG.3) The rocker switch has a “1” and “0” printed

on it. When the “1” is pressed down the changer is “ON”.

MOUNTING THE AC2001 TO A WALL

IF YOU ARE UNSURE IN ANY WAY IN PROCEEDING

WITH THE FOLLOWING STEPS, PLEASE HIRE A LOCAL

PROFESSIONAL ELECTRICIAN TO MOUNT YOUR

CHANGER FOR YOU!

1. Disconnect any and all AC power going to the series 2001

changer. (See fig. 1)

A. Unplug the AC line cord from the bottom of the board.

B. Unplug the validator connectors on the right side of the

board.

C. Unplug the hoppers harness connectors on the left side

of the board.

D. Unbolt the ground wire from the right side of the

cabinet.

E. Remove the main logic board and hoppers from the

inside of the changer.

F. Put the nuts back on the studs to avoid losing the brass

spacers on the studs.

2. Slide the hoppers out of the cabinet.

3. Note: You will need to verify with the building code that it

is allowable to plug the changer into a 3 prong grounded

outlet. If it is not, there must be 120VAC run through

conduit to the changer. If it is not required, proceed to step

#6.

4. Let the electrician run the conduit, install the new breaker,

wire and help decide how the wiring will enter the changer

(from the back or the bottom). This will affect the

mounting location.

5. After the conduit has been installed, proceed with the

mounting.

6. Locate the 4 punch-outs on the back wall of the changer.

Using a screwdriver and hammer knock the punch-outs

out by hitting them from the inside of the changer.

7. Using a stud locator, find a location to hang the changer

by locating the wall studs.

8. Find an appropriate wall to bolt the changer into. The

wall should have studs or be constructed of concrete.

Consult a professional with any questions you may

have.

9. NOTE: HANGING THE CHANGER FROM LESS

THAN ALL 4 HOLES MAY BE DANGEROUS.

EACH HOLE NEEDS A BOLT THROUGH EACH

ONE MOUNTED SECURELY TO THE WALL.

MOUNTING THE CHANGER IN ANY OTHER WAY

MAY RESULT IN THE CHANGER BEING TORN

OFF OR FALLING OFF THE WALL RESULTING

IN PERSONAL OR CUSTOMER INJURY ALONG

WITH ELECTRICAL SHOCK.

10. Choose a height to mount the changer keeping in mind

that a handicapped person in a wheelchair should still be

able to insert a bill into the bill validator. (We

recommend no higher than 4 feet above the ground.)

11. Have someone hold the changer against the wall while

someone else marks the holes. CAUTION: THE

CHANGER WEIGHS 85 POUNDS DO NOT EXERT

YOURSELF SO THAT YOU MAY CAUSE AN

INJURY.

12. BEFORE DRILLING THE FOUR MARKED HOLES

ENSURE THAT THERE ARE NO ELECTRICAL

WIRES, TELEPHONE LINES, GAS, OR WATER

LINES BEHIND THE WALL WHICH DISRUPTING

MAY CAUSE A LOSS OF LIFE OR PERSONAL

INJURY!

13. Hold the changer back up to the wall. Thread and

tighten bolts.

14. Verify that the machine is securely mounted.

15. Reinstall the main logic board.

A. Before installing the main logic board, verify that

the plastic safety-insulating sheet is still against the

back wall where the board will be mounted and

that there is a 3/8” spacer on each stud.

B. Install the main logic board and properly tighten

the nuts.

C. Re-bolt the ground wire into the right side of the

cabinet.

D. Plug the validator connector into the right side of

the board.

E. Plug the hoppers harness connectors into the left

side of the board

16. If the changer is permanently connected through a

conduit, proceed to step #18.

17. Feed the AC line cord out the bottom or the back of the

changer then perform the following.

A. Connect the AC line cord into the bottom of the

main logic board.

B. Plug the male end into the AC wall outlet. Do not

use an extension cord unless allowed by the

building electrical code.

C. Important: Attach the line cord clamp to the line

cord. Verify it is at the right length and that the line

NOTE: The only way to get a duplicate set of keys

made is to save the red tag that comes between the

keys. This ID # starts with “ACC ####”.

Write your Key # here “ACC_____________”.

ALL KEY ORDERS TAKE 4-6 WEEKS!!!

1 2 3 4 5 6 7 8 ... 44 45

Kommentare zu diesen Handbüchern

Keine Kommentare

Black Box AC2000A Spezifikationen Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Black Box AC2000A