Black Box IC109A-R2 Installationshandbuch Seite 38
- Seite / 164
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
32
© 2007 Schneider Electric. All Rights Reserved.
1
63230-216-229-B1
Installation
1A/5A Current Transformers
MT10490
Connecting and Assembling the CCA630 Connector
1 Open the two side shields for access to the connection terminals. The shields can
be removed to make wiring easier. If removed, replace them after wiring.
2 Remove the bridging strap linking terminals 1, 2, and 3. This strap is supplied with
the CCA630.
3 Connect the wires using 4 mm (0.16 in) ring lugs and check the tightness of the
six screws that guarantee the continuity of the CT secondary circuits. The
connector accommodates wires with cross-sections of 1.5 to 6 mm²
(AWG 16-10).
4 Close the side shields.
5 Plug the connector into the 9-pin inlet on the rear panel (item ).
6 Tighten the two CCA630 connector fastening screws on the rear panel of
Sepam™.
.
DE80068
DE80069
Connecting and Assembling the CCA634 Connector
1 Open the two side shields for access to the connection terminals. The shields can
be removed, if necessary, to make wiring easier. If removed, replaced them after
wiring.
2 According to the wiring required, remove or reverse the bridging strap. This is
used to link either terminals 1, 2, and 3, or terminals 1, 2, 3, and 9 (see picture
opposite).
3 Use terminal 7 (1A) or 8 (5A) to measure the residual current according to the
CT secondary.
4 Connect the wires using 4 mm (0.16 in) ring lugs and check the tightness of the
six screws that guarantee the continuity of the CT secondary circuits. The
connector accommodates wires with cross-sections of 1.5 to 6 mm²
(AWG 16-10). The wires only exit from the base.
5 Close the side shields.
6 Insert the retaining tabs into the slots on the base unit.
7 Pivot the connector toward the unit to plug it into the 9-pin SUB-D connector
(principle similar to that of the MES module).
8 Tighten the mounting screw.
Bridging terminals
1, 2, 3, and 9
Bridging terminals
1, 2, and 3
CAUTION
HAZARD OF IMPROPER OPERATION
Do not use a CCA634 on connector B1 and
residual current input Ir on connector E
(terminals 14 and 15) simultaneously.
b Though unconnected to a sensor, a
CCA634 on connector B1 will disturb input
Ir on connector E.
Do not use a CCA634 on connector B2 and
residual current input I'r on connector E
(terminals 17 and 18) simultaneously.
b Though unconnected to a sensor, a
CCA634 on connector B2 will disturb input
I'0 on connector E.
Failure to follow this instruction can cause
equipment damage.
B
1
2
3
6
5
4
7 (1A)
8 (5A)
9
CCA634
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern