Black Box IC109A-R2 Installationshandbuch Seite 88
- Seite / 164
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
82
2
© 2007 Schneider Electric. All Rights Reserved.63230-216-229-B1
Use
Local Operation on the UMI
Types of Operations and Passwords
Types of Operations
The Sepam™ UMI can perform three types of operations:
b normal operations, such as consulting operating information, resetting
Sepam™ and current alarms acknowledgement
b protection settings, like modifying the tripping set point of an active protection
function
b modifying Sepam™ parameters: for example, change the operating language
or set the internal clock
Protection setting and parameter operations require a password.
Passwords
Protection setting and parameter operations are protected by two different
passwords, each having four digits:
b password for protection settings
b password for parameter settings
The default passwords are 0000.
The table below indicates the operations authorized for each password.
Operations No Password Protection-Setting
Password
Parameter-Setting
Password
Normal operation bbb
Set the active
protection functions
(1)
bb
Modify Sepam™
parameters
b
DE51564
Entering Passwords
Perform the following steps to enter a password:
1 Press to access the screen for password entry.
2 Press to position the cursor on the first digit.
3 Press the cursor keys and as needed to scroll through the digits.
4 Press to confirm and go to the next digit.
(Do not use characters other than numbers 0 to 9 for each of the 4 digits.)
5 After the four digits are entered, press to position the cursor on [Apply].
6 Press again to confirm.
Validating Passwords
Password Validity
After entering the protection-setting password, the icon displays at the top of
the screen.
After entering the parameter-setting password, the icon displays at the top of
the screen.
The icon remains displayed as long as the password is valid, and the corresponding
operations are authorized.
End of Validity
A password is deactivated either by pressing or automatically if no keys are
activated for more than 5 minutes.
Loss of Passwords
Contact a technical support representative for information.
(1) SFT2841 software required
Screen for password entry.
DE51565
Indication of password validity on the display:
= password for protection settings is valid.
= password for parameter settings is valid.
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern